[Specs & Pics] GTC Integral

Couteaux pliants de tous genres et de toutes tailles

Re: [Specs & Pics] GTC Integral

Messagepar pwet » 22 Fév 2012 16:59

ouaip pour pouvoir arrondir il est evident que le fraisage doit etre a l'interieur mais je parlais plus de ca.


RJ Martin a écrit:Consider the lock to be acting as a column supported where the lock bar cutout starts. Ideally, the lockbar would be directly behind the blade, and precisely in-line with the centerline of the blade. Then, the load on the column (lock bar) would be purely vertical. Of course, this is impossible, as the column (lock) needs to be off-center so that there is room for the blade to close. But, putting the lock cut-out on the outside means that the lock-bar needs to bend at a smaller angle in order to engage the tang of the knife. Thus, the column is more nearly vertically oriented. More vertical=harder to push off-center, which is one way that locks fail.

If you make an analogy to cutting down two trees, one that stands perfectly vertical, and one that leans, you will see what I am saying. For the vertical tree, you will have to progress pretty far with the felling cut, and possible need to push (or pull) the tree to get it to fall. The leaning tree will fall much easier, because gravity is helping you and the tree is already unstable.

Fun stuff to think about.………..

Now, this is a small point-You can certainly make strong, reliable locks in either configuration (I have made them both ways), but, putting the cut on the outside definitely keeps the line of force on the lock more in-line with the blade/centerline of the knife. How the geometry of the tang interfaces with the end of the lock bar can have a much more significant impact on lock failure than which side of the lock is relieved.

As to the points about leaving enough material for strength vs. having a lock that is too stiff to manipulate, that can be balanced by choosing the right width for the lock bar. For two locks, relieved to the same thickness, a narrower lock will release more easily than a taller(wider) lock.


extrait d'ici http://www.bladeforums.com/forums/showt … k-cut-outs
recherche : anciens spyderco military cpm440V SE ou PE, voire ats 34.

merci
Avatar de l’utilisateur
pwet
Théoricien de lâme
 
Messages: 5973
Inscrit le: 22 Oct 2008 01:51
Localisation: back to marseille city !

Re: [Specs & Pics] GTC Integral

Messagepar panerai » 09 Oct 2012 22:38

Possesseurs ou pro de GTC une question: sont ils tous gravés à la main ? (au crayon électrique apparemment) si c'est l'cas je trouve cela chicos .
Dans le sens de l'ouverture sur ces couteaux pourvus de flipper, les lames sont libre comme l'air ? pas de loup à les avoir dans une fouille ? (sans étui s'entend)

Kcnarf.
Avatar de l’utilisateur
panerai
 
Messages: 480
Inscrit le: 20 Sep 2012 23:34

Re: [Specs & Pics] GTC Integral

Messagepar Digaboy » 10 Oct 2012 08:14

je ne comprend pas ce que tu sous entend par "fouille" mais généralement ce sont des liners le flipper permet juste l'ouverture fluide et rapide
Avatar de l’utilisateur
Digaboy
 
Messages: 1647
Inscrit le: 28 Mar 2010 21:37
Localisation: Grenoble

Re: [Specs & Pics] GTC Integral

Messagepar Berno » 10 Oct 2012 08:25

Euh t'es si jeune que ça Digaboy ?? :mouarf:

Ha oui, 24 ….

Je ne sais pas si on peut parler d'argot, mais une fouille c'est tout simplement une poche.… :wink:
Avatar de l’utilisateur
Berno
Gluon
 
Messages: 4597
Inscrit le: 24 Nov 2008 11:07

Re: [Specs & Pics] GTC Integral

Messagepar Digaboy » 10 Oct 2012 09:46

aaahhhhh dans la poche !!

ces vieux et leurs expressions :mouarf: :mouarf:

généralement tu as une bille qui assure une rétention du couteau en position fermé et demande une poussé plus ou moins franche pour être ouverte.
Donc tu appuie sur le flipper et un moment la bille n’assure plus la rétention du couteau en position fermé, à ce moment là tu as pas mal de force sur le flipper donc ça s'ouvre d'un coup !

(je sais pas si je suis très clair là …)
Avatar de l’utilisateur
Digaboy
 
Messages: 1647
Inscrit le: 28 Mar 2010 21:37
Localisation: Grenoble

Re: [Specs & Pics] GTC Integral

Messagepar .LuD. » 10 Oct 2012 09:53

Sisi
En vert et contre tous !
Avatar de l’utilisateur
.LuD.
 
Messages: 19821
Inscrit le: 01 Fév 2008 16:31
Localisation: - Somewhere in space.

Re: [Specs & Pics] GTC Integral

Messagepar Berno » 10 Oct 2012 09:54

Quelle tristesse cette jeunesse....Aucune culture... :wink:
Avatar de l’utilisateur
Berno
Gluon
 
Messages: 4597
Inscrit le: 24 Nov 2008 11:07

Re: [Specs & Pics] GTC Integral

Messagepar Berno » 10 Oct 2012 09:58

Le problème c'est qu'avec Gus tout est possible, perso celui ci en intégral me fait de l'oeil...

Image
Avatar de l’utilisateur
Berno
Gluon
 
Messages: 4597
Inscrit le: 24 Nov 2008 11:07

Re: [Specs & Pics] GTC Integral

Messagepar .LuD. » 10 Oct 2012 10:16

Ah ouais...
En vert et contre tous !
Avatar de l’utilisateur
.LuD.
 
Messages: 19821
Inscrit le: 01 Fév 2008 16:31
Localisation: - Somewhere in space.

Re: [Specs & Pics] GTC Integral

Messagepar jlg » 10 Oct 2012 10:20

Il s'appelle comment ?

Je vais faire une grosse entorse à mes choix habituels :oops:

Mon prochain aura un flippe.
jlg
 
Messages: 27680
Inscrit le: 24 Mai 2007 15:11

Re: [Specs & Pics] GTC Integral

Messagepar Berno » 10 Oct 2012 10:21

C'est dans la gamme supersonic...
Avatar de l’utilisateur
Berno
Gluon
 
Messages: 4597
Inscrit le: 24 Nov 2008 11:07

Précédent

Retour vers Couteaux pliants

Qui est en ligne ?

Utilisateurs parcourant actuellement ce forum : Aucun utilisateur inscrit et 11 invités